For many botanists, they want to move the plants from one area to another without damaging or completely killing the plants. This has been considered a convenient method as opposed to growing them which takes a lot of time and effort. Relocation of Growing Cycads through using their parent plants has been often used for conservation or commercial reasons.
The first stage of relocating the plant is through cutting the older leaves that are often at the bottom of the tree. This is done to reduce the effort on the root as it recovers from the move to supply the necessary nutrients to the rest of the plant. The directional orientation of the leaves is also identified through tagging the direction of some leaves so as to set them appropriately when moved.
Afterwards, the diameter of the caudex is measured. The digit is usually very important as it determines the depth and diameter of the hole dug to remove the tree. The caudex diameter is added 3 or 4 times to acquire a diameter in which the hole around the tree is to be dug, as well as the diameter of the hole to be dug underground. The caudex is mainly used to store water.
If the holes are properly dug, then the process of removing the tree will be easier when pulling it. However, the investors need to be extra cautious when removing the tree so as to avoid damaging the roots as this may lengthen its recovery time. Additionally, the extra weight of plants due to soil on the roots is also removed by hosing.
On removing the roots and hosing off the extra soil, the person relocating the plant needs to check the condition of all roots for any extensive damage. During the check, they should also cut out the ragged roots attached to the root ball but are outside it. The roots are then treated with fungicide and rooting hormone so as to ensure they are not affected by pests or end up rotting.
Moving the tree will require using a machine and a vehicle. The plant can either be moved so as to be potted, boxed or relocated to a new location. For relocation, the mover needs to have found a good spot for the plant. For example, a cycad needs well drained soil often sandy in a sloppy area. While transportation, further root damage needs to be avoided.
The area is then prepared through digging a 1 and a half bigger hole diameter and deepness than that of the root ball. The plant is then put in place and covered with soil. The directional orientation of leaves should be observed as the tree is being set to reduce strain on it to adapt to the new location. The soil depth should also be noted as it should be similar to that on the plant while in the old location.
On placing in the trees, an earth trench should be dug around it in which 5 gallons of water with rooting hormone is placed which should last for 2-3 weeks. The resulting first leaves may not be similar to that while in the old location, but they will get better with the next season.
The first stage of relocating the plant is through cutting the older leaves that are often at the bottom of the tree. This is done to reduce the effort on the root as it recovers from the move to supply the necessary nutrients to the rest of the plant. The directional orientation of the leaves is also identified through tagging the direction of some leaves so as to set them appropriately when moved.
Afterwards, the diameter of the caudex is measured. The digit is usually very important as it determines the depth and diameter of the hole dug to remove the tree. The caudex diameter is added 3 or 4 times to acquire a diameter in which the hole around the tree is to be dug, as well as the diameter of the hole to be dug underground. The caudex is mainly used to store water.
If the holes are properly dug, then the process of removing the tree will be easier when pulling it. However, the investors need to be extra cautious when removing the tree so as to avoid damaging the roots as this may lengthen its recovery time. Additionally, the extra weight of plants due to soil on the roots is also removed by hosing.
On removing the roots and hosing off the extra soil, the person relocating the plant needs to check the condition of all roots for any extensive damage. During the check, they should also cut out the ragged roots attached to the root ball but are outside it. The roots are then treated with fungicide and rooting hormone so as to ensure they are not affected by pests or end up rotting.
Moving the tree will require using a machine and a vehicle. The plant can either be moved so as to be potted, boxed or relocated to a new location. For relocation, the mover needs to have found a good spot for the plant. For example, a cycad needs well drained soil often sandy in a sloppy area. While transportation, further root damage needs to be avoided.
The area is then prepared through digging a 1 and a half bigger hole diameter and deepness than that of the root ball. The plant is then put in place and covered with soil. The directional orientation of leaves should be observed as the tree is being set to reduce strain on it to adapt to the new location. The soil depth should also be noted as it should be similar to that on the plant while in the old location.
On placing in the trees, an earth trench should be dug around it in which 5 gallons of water with rooting hormone is placed which should last for 2-3 weeks. The resulting first leaves may not be similar to that while in the old location, but they will get better with the next season.
About the Author:
When you are looking for information about growing cycads, go to our web pages online here today. More details are available at http://stores.botanicwonders.com/cycads now.
Tidak ada komentar:
Posting Komentar